Enable the “inband SAS” feature, it will close the ethernet port to prevent resource confliction. You will be not able to login the controller through ethernet if you enable inband SAS. If you would like to configure the controller, you must use inband SAS or serial port. You have to use the RJ11 to RS232 cable to login the controller serial manager console through the RJ11 connector on the ARC-8060.
Tags: ARC-8060, ethernet, SAS- FAQ Home
- All categories
- SATA/SAS PCI RAID Card
- Mezzanine Board
- SAS Non-RAID Adapters
- External RAID Controllers
- JBOD/Expander Box
- Desktop RAID Subsystem
- Internal RAID Rack
- Thunderbolt Solutions
3 users online | 3 Guests and 0 Registered
Q40011108 - After changing the "Inband SAS enable" to enabled in the telnet interface of our ARC-8060, the telnet and web interface are not available.
- Last update:
- 2021-02-04 10:20
- Author:
- Simone
- Revision:
- 1.2
You cannot comment on this entry
Records in this category
- Q10081501 - How do we identify slow hard disk on Areca RAID Controller?
- Q10091501 - Does “TLER Setting” on system configuration translate to ERC (Seagate) and CCTL (Samsung/Hitachi) or is it only a valid setting for WD drives that have TLER?
- Q40011501 - How can we update the on-board expander firmware on the external RAID controllers?
- Q40011504 - Does ARC-8088 support a SFP-to-RJ45 adapter?
- Q40021504 - Is ARC-8088-iSCSI controller just MPIO or it supports MC/S also?
- Q40031504 - Always setup each 10G NIC with different IP, but the same subnet or different subnet? On the Initiator side, what to do with single NIC and what to do for dual NICs?
- Q40011505 - Does Areca CLI support external RAID controller using lan port?
- Q10051403 - How is the cable length used on first hop from 3008/3108 to expander?
- Q10091403 - How is the cable length used on first hop from 3008/3108 to expander?
- Q10121403 - Flashing disk drives attached to an Areca RAID controller.
- Q10131403 - Locate and identify drives in an enclosure or backplane with Fault/Activity LEDs.
- Q10181403 - How to rebuild a degraded RAID set on a SATA or SAS RAID controller?
- Q10191403 - Are 4TB drives supported on Areca RAID controllers?
- Q40011403 - Does SATA 1.5G support by ARC-8080/8008 external 12Gb/s SAS RAID controller?
- Q40021403 - ARC-8068 encountered a “Time Out Error” with Intel S3500 SSD.
- Q40011405 - 12Gb/s SAS HDD can not power up on the some 6Gb/s SAS backplanes.
- Q40011406 - We would like to know how to turn off telnet for the ARC-8068.
- Q10061406 - I have set "Alert By Mail Configuration" and configured: Send Only Urgent Event. However, I am receiving emails with subject "RaidAlert-WARNING".
- Q40011407 - With an ARC-8068 (which has one volume on it) attached to a 9200-8e LSI HBA that causes a blue screen with "BAD_POOL_CALLER" on 2012R2. Setup works fine under Windows 7 and 2008.
- Q40011408 - Connecting an AIC XJ3000-4603M with 60 drives to an ARC-8007 RAID controller, the ARC-8007 only sees 6 of the 60 drives.
- Q10031411 - Areca RAID controllers can only detect 10 HDDs with Quanta M4600H 60-bays JBOD.
- Q10061412 - Controller fails the brand new hard drive when runs the Hdd Xfer Speed function.
- Q40011305 - LSI SAS switch only sees the first volume/LUN from the 8068 and not any of the others. All connected hosts see all volumes.
- Q40021305 - Do ARC-8006/8007 external raid controller support ALUA on redundant controller mode?
- Q40011204 -The LED lights on st3000DM001 HDD's with firmware CC46 continues to flash even no activity. We tried with other disks and they work normal.
- Q40011108 - After changing the "Inband SAS enable" to enabled in the telnet interface of our ARC-8060, the telnet and web interface are not available.
- Q40011508 - USB 3.0 Port of the 5040 sometimes detects only with 2.2TB Size (original size 18TB) in combination with Macbooks or Notebooks which are built 2014 or newer.
- Q10041508 - Does Areca RAID adapter support the new WD 5TB/6TB HDD firmware update function code about 5MB in size?
- Q10011509 - Does Areca RAID adapter support write back cache with battery backed RAM on JBOD disks or passthrough disk?
- Q10011512 - One SSD Disk fails in the ARC-1883i Raid Set a while in usage. After changing the Disk, it fails after a few hours again.
Tags
12Gb/s SAS expander 4KN drive Acronis Advanced Data Mirroring AJA Alert By Mail Configuration ALUA AOC API ARC-1035 ARC-1130 ARC-1200 ARC-1201 ARC-1202 ARC-1203 ARC-1203-2I ARC-1210 ARC-1212 ARC-1213 ARC-1213-4i ARC-1214 ARC-1214-4I Arc-1214-8I ARC-1220 ARC-1221 ARC-1221x ARC-1222 ARC-1223 ARC-1223-8i ARC-1223-8X ARC-1224 ARC-1224-8I ARC-1225-8I ARC-1230-8x ARC-1231 ARC-1231Ml ARC-1260 ARC-1261ML ARC-1264il-12 ARC-1264il-16 ARC-1280 ARC-1280ML ARC-12x3 ARC-12x4 ARC-12x5 ARC-12x6 ARC-1300 ARC-1300-4e ARC-1300-4i ARC-1300ix-16