Areca FAQ System - Q40011504 - Does ARC-8088 support a SFP-to-RJ45 adapter?

Q40011504 - Does ARC-8088 support a SFP-to-RJ45 adapter?

ARC-8088 10G iSCSI can’t negotiate at 1G. SFP-to-RJ45 adapter is not working on our iSCSI 10G.

Tags: ARC-8088, Q40011504

Last update:: 2021-02-04 10:30
Author:: Simone
Revision:: 1.2

You cannot comment on this entry

Records in this category

Q10081501 - How do we identify slow hard disk on Areca RAID Controller?
Q10091501 - Does “TLER Setting” on system configuration translate to ERC (Seagate) and CCTL (Samsung/Hitachi) or is it only a valid setting for WD drives that have TLER?
Q40011501 - How can we update the on-board expander firmware on the external RAID controllers?
Q40011504 - Does ARC-8088 support a SFP-to-RJ45 adapter?
Q40021504 - Is ARC-8088-iSCSI controller just MPIO or it supports MC/S also?
Q40031504 - Always setup each 10G NIC with different IP, but the same subnet or different subnet? On the Initiator side, what to do with single NIC and what to do for dual NICs?
Q40011505 - Does Areca CLI support external RAID controller using lan port?
Q10051403 - How is the cable length used on first hop from 3008/3108 to expander?
Q10091403 - How is the cable length used on first hop from 3008/3108 to expander?
Q10121403 - Flashing disk drives attached to an Areca RAID controller.
Q10131403 - Locate and identify drives in an enclosure or backplane with Fault/Activity LEDs.
Q10181403 - How to rebuild a degraded RAID set on a SATA or SAS RAID controller?
Q10191403 - Are 4TB drives supported on Areca RAID controllers?
Q40011403 - Does SATA 1.5G support by ARC-8080/8008 external 12Gb/s SAS RAID controller?
Q40021403 - ARC-8068 encountered a “Time Out Error” with Intel S3500 SSD.
Q40011405 - 12Gb/s SAS HDD can not power up on the some 6Gb/s SAS backplanes.
Q40011406 - We would like to know how to turn off telnet for the ARC-8068.
Q10061406 - I have set "Alert By Mail Configuration" and configured: Send Only Urgent Event. However, I am receiving emails with subject "RaidAlert-WARNING".
Q40011407 - With an ARC-8068 (which has one volume on it) attached to a 9200-8e LSI HBA that causes a blue screen with "BAD_POOL_CALLER" on 2012R2. Setup works fine under Windows 7 and 2008.
Q40011408 - Connecting an AIC XJ3000-4603M with 60 drives to an ARC-8007 RAID controller, the ARC-8007 only sees 6 of the 60 drives.
Q10031411 - Areca RAID controllers can only detect 10 HDDs with Quanta M4600H 60-bays JBOD.
Q10061412 - Controller fails the brand new hard drive when runs the Hdd Xfer Speed function.
Q40011305 - LSI SAS switch only sees the first volume/LUN from the 8068 and not any of the others. All connected hosts see all volumes.
Q40021305 - Do ARC-8006/8007 external raid controller support ALUA on redundant controller mode?
Q40011204 -The LED lights on st3000DM001 HDD's with firmware CC46 continues to flash even no activity. We tried with other disks and they work normal.
Q40011108 - After changing the "Inband SAS enable" to enabled in the telnet interface of our ARC-8060, the telnet and web interface are not available.
Q40011508 - USB 3.0 Port of the 5040 sometimes detects only with 2.2TB Size (original size 18TB) in combination with Macbooks or Notebooks which are built 2014 or newer.
Q10041508 - Does Areca RAID adapter support the new WD 5TB/6TB HDD firmware update function code about 5MB in size?
Q10011509 - Does Areca RAID adapter support write back cache with battery backed RAM on JBOD disks or passthrough disk?
Q10011512 - One SSD Disk fails in the ARC-1883i Raid Set a while in usage. After changing the Disk, it fails after a few hours again.